Effect of basket mesh size on the hydrodynamics of a partially filled (500 mL) USP rotating basket dissolution testing Apparatus 1.

The USP Rotating Basket Dissolution Testing Apparatus 1 is listed in the USP as one of the tools to assess dissolution of oral solid dosage forms. Baskets of different mesh sizes can be used to differentiate between dissolution profiles of different formulations. Here, we used Particle Image Velocimetry (PIV) to study the hydrodynamics of the USP Apparatus 1 using baskets with different mesh openings (10-, 20- and 40-mesh) revolving at 100 rpm, when the vessel was filled with 500 mL. The velocity profiles throughout the liquid were found to vary significantly using baskets of different mesh sizes, typically increasing with increased size of the opening of the basket mesh, especially for axial and radial velocities. This, in turn, resulted in a significantly different flow rate through the basket, which can be expected to significantly impact the dissolution rate of the drug product. A comparison between the results of this work with those of a previous study with a 900-mL fill volume (Sirasitthichoke et al., Intern. J. Pharmaceutics, 2021, 607: 120976), shows that although the hydrodynamics in the USP Apparatus 1 changed with fill level in the vessel, the flow rate through the basket was not significantly affected. This implies that tablets dissolving in the two systems would experience similar tablet-liquid medium mass transfer coefficients, and therefore similar initial dissolution rates, but different dissolution profiles because of the difference in volume.

CFD-based bioreactor model with proportional-integral-derivative controller functionality for dissolved oxygen and pH.

A physics-based model for predicting cell culture fluid properties inside a stirred tank bioreactor with embedded PID controller logic is presented. The model evokes a time-accurate solution to the fluid velocity field and overall volumetric mass transfer coefficient, as well as the ongoing effects of interfacial mass transfer, species mixing, and aqueous chemical reactions. The modeled system also includes a direct coupling between process variables and system control variables via embedded controller logic. Satisfactory agreement is realized between the model prediction and measured bioreactor data in terms of the steady-state operating conditions and the response to setpoint changes. Simulation runtimes are suitable for industrial research and design timescales.

Particle Image Velocimetry (PIV) measurements of USP Apparatus 1 hydrodynamics with 500 mL fill volume.

Changes to hydrodynamics arising from changes within dissolution testing systems, such as the fill volume level, can potentially cause variability in dissolution results. However, the literature on hydrodynamics in Apparatus 1 is quite limited and little information is available for vessels with different liquid volumes. Here, velocities in a USP Apparatus 1 vessel with a liquid fill volume of 500 mL, a common alternative to 900 mL, were experimentally measured using 2D-2C Particle Image Velocimetry (PIV) for different basket rotational speeds. Tangential velocities dominated the flow field, while axial and radial velocities were much lower and varied with location. The velocities distribution increased proportionately with the basket rotational speed almost everywhere in the vessel excepting for underneath the basket. A nearly horizontal radial liquid jet was found to originate close to the basket upper edge. Comparison of these results with those previously reported with 900-mL liquid volume (Sirasitthichoke et al., Intern. J. Pharmaceutics:X; 3 (2021) 100078) showed that the flow rate through the baskets was similar in both systems, implying that, at least initially, the amount of drug in solution would increase linearly with time. In other words, the flow rate through the baskets would be independent of the liquid volume. Velocity profiles were also found to be similar, except in the region above the basket, which was affected by the radial jet with an orientation significantly different between the 500-mL and the 900-mL systems.

Computational prediction of blend time in a large-scale viral inactivation process for monoclonal antibodies biomanufacturing.

Viral inactivation (VI) is a process widely used across the pharmaceutical industry to eliminate the cytotoxicity resulting from trace levels of viruses introduced by adventitious agents. This process requires adding Triton X-100, a non-ionic detergent solution, to the protein solution and allowing sufficient time for this agent to inactivate the viruses. Differences in process parameters associated with vessel designs, aeration rate, and many other physical attributes can introduce variability in the process, thus making predicting the required blending time to achieve the desired homogeneity of Triton X-100 more critical and complex. In this study we utilized a CFD model based on the lattice Boltzmann method (LBM) to predict the blend time to homogenize a Triton X-100 solution added during a typical full-scale commercial VI process in a vessel equipped with an HE-3-impeller for different modalities of the Triton X-100 addition (batch vs. continuous). Although direct experimental progress of the blending process was not possible because of GMP restrictions, the degree of homogeneity measured at the end of the process confirmed that Triton X-100 was appropriately dispersed, as required, and as computationally predicted here. The results obtained in this study were used to support actual production at the biomanufacturing site.

Influence of basket mesh size on the hydrodynamics in the USP rotating basket dissolution testing Apparatus 1.

The USP Apparatus 1 (rotating basket), typically used to assess drug product reproducibility and evaluate oral solid dosage forms performance, consists of a cylindrical glass vessel with a hemispherical bottom and a wire basket rotating at constant speed. Baskets with different wire openings can be used in alternative to the standard mesh opening (40-mesh) in order to discriminate between drug formulations during early stage of drug product development. Any changes introduced by different basket geometries can potentially and significantly impact the system hydrodynamics and cause variability of results, thus affecting product quality. In this work, Particle Image Velocimetry (PIV) was used to experimentally quantify the velocity distribution in the USP rotating basket Apparatus 1 using baskets of different mesh sizes (10-, 20-, and 40-mesh size) under the typical operating conditions described in dissolution testing procedures. Similar flow patterns were observed in all cases. However, the radial and axial velocities in the USP Apparatus 1 generally increased with increasingly larger openings of the basket mesh. Increasing the basket agitation speed also resulted in an overall increase in the velocities, especially below in the innermost core region below the basket, where drug fragments typically reside. More importantly, the flow entering and leaving the baskets was quantified from the velocity profiles in the immediate vicinity of the baskets. It was found that the flow increased significantly with increasingly larger mesh openings, which can, in turn, promote faster dissolution of the oral solid dosage forms, thus affecting drug dissolution profiles. Hence, the selection of the basket mesh size must be carefully considered during drug product development.

Experimental determination of the velocity distribution in USP Apparatus 1 (basket apparatus) using Particle Image Velocimetry (PIV).

The USP Apparatus 1 (basket apparatus) is commonly used to evaluate the dissolution performance of oral solid dosage forms. The hydrodynamics generated by the basket contributes, in general, to the dissolution rate and hence the dissolution results. Here, the hydrodynamics of Apparatus 1 was quantified in a vessel filled with 900-mL de-ionized water at room temperature by determining, via Particle Image Velocimetry (PIV), the velocity profiles on a vertical central plane and on 11 horizontal planes at different elevations at three different basket agitation speeds. The flow field was dominated by the tangential velocity component and was approximately symmetrical in all cases. Despite all precautions taken, small flow asymmetries were observed in the axial and radial directions. This appears to be an unavoidable characteristic of the flow in Apparatus 1. The magnitudes of the axial and radial velocity components varied with location but were always low. A small jet was seen emanating radially near the top edge of the basket. Velocities typically scaled well with increasing agitation speed in most regions of the vessel except for a region directly below the basket. The results of this work provide a major insight into the flow field inside the USP Apparatus 1.